The MKS-70 Controller reaches 126 parameters in 24 groups: the patch level, the per-half settings stored in the patch, the tone parameters of each half, and 8 bytes Roland never documented. The tables below are generated from the parameter table of the app itself.
How to read the tables
- Range lists the choices for a switch, or the lowest and highest value for a continuous control.
- Address is where the parameter lives.
Patch 0x12 is a patch-level address. Tone 1 · 34 (0x22) is tone address 34 of the Upper half; Tone 2 is the Lower half.
- Groups whose name ends in Extensions exist only on Vecoven 4.x firmware. The app hides and never sends them under any other firmware setting. See Firmware.
With a Vecoven firmware setting, each edit is one Individual Parameter (IPR) message:
Tone: F0 41 36 [unit] 24 20 [tone] [address] [value] F7 tone 01 = Upper, 02 = Lower
Patch: F0 41 36 [unit] 24 30 01 [address] [value] F7
[unit] is the SysEx device number from Settings → MIDI, which follows the MIDI channel unless you set it. With the Original Roland setting, the app sends the whole patch or tone block (All Parameters, APR, command 0x35) instead, with the value placed at the same address inside the block. Switch values are sent in the encoding the unit expects, which is not always the position number shown here.
Patch
Patch-level parameters, shared by both halves.
| Parameter |
Range |
Address |
Notes |
| Upper/Lower Balance |
0 to 127 |
Patch 0x12 |
The Listen switch in the header, and the crossfader in the Tones panel. Default 64. |
| Patch Volume |
0 to 127 |
Patch 0x19 |
The Volume knob in the header, read in decibels (0 dB at 127, about −55 dB at 0). Default 127. |
| Portamento |
0 to 127 |
Patch 0x14 |
Set together with Portamento Time by the Porta switch in the Chorus · Glide panel. Not written on the Original Roland ROM setting. Default 0. |
| Portamento Time |
0 to 127 |
Patch 0x16 |
Porta Time in the Chorus · Glide panel. Moving it above 0 also switches portamento on. Default 0. |
Upper Tone
Per-half settings stored in the patch for the Upper half.
| Parameter |
Range |
Address |
Notes |
| Tone Number |
0 to 127 |
Patch 0x1D |
Writing it makes the unit load that stored tone into this half. Not available to the modulation matrix. Default 0. |
| Key Shift |
−24 to +24 |
Patch 0x1E |
Semitones, up to two octaves either way. Default 0. |
| Key Assign |
Poly 1, Unison 1, Mono 1, Poly 2, Unison 2, Mono 2 |
Patch 0x1F |
Key Assign menu on the Tones panel. Not available to the modulation matrix. Default Poly 1. |
| Unison Detune |
0 to 103 |
Patch 0x20 |
Detune on the Tones panel. Heard only with a Unison key assign. Default 0. |
| Hold |
Off, On |
Patch 0x21 |
Hold on the Tones panel. Default Off. |
| LFO Mod Depth |
0 to 126 |
Patch 0x22 |
Wheel LFO on the Tones panel: how far the mod wheel (CC 1) opens the LFO. Default 0. |
| Portamento |
Off, On |
Patch 0x23 |
Porta on the Tones panel. On the Original Roland ROM this is what the Porta switch in the Chorus · Glide panel writes. Default Off. |
| Pitch Bend |
Off, On |
Patch 0x24 |
Whether the pitch wheel bends this half. Default On. |
Lower Tone
Per-half settings stored in the patch for the Lower half.
| Parameter |
Range |
Address |
Notes |
| Tone Number |
0 to 127 |
Patch 0x26 |
Writing it makes the unit load that stored tone into this half. Not available to the modulation matrix. Default 0. |
| Key Shift |
−24 to +24 |
Patch 0x27 |
Semitones, up to two octaves either way. Default 0. |
| Key Assign |
Poly 1, Unison 1, Mono 1, Poly 2, Unison 2, Mono 2 |
Patch 0x28 |
Key Assign menu on the Tones panel. Not available to the modulation matrix. Default Poly 1. |
| Unison Detune |
0 to 103 |
Patch 0x29 |
Detune on the Tones panel. Heard only with a Unison key assign. Default 0. |
| Hold |
Off, On |
Patch 0x2A |
Hold on the Tones panel. Default Off. |
| LFO Mod Depth |
0 to 126 |
Patch 0x2B |
Wheel LFO on the Tones panel: how far the mod wheel (CC 1) opens the LFO. Default 0. |
| Portamento |
Off, On |
Patch 0x2C |
Porta on the Tones panel. On the Original Roland ROM this is what the Porta switch in the Chorus · Glide panel writes. Default Off. |
| Pitch Bend |
Off, On |
Patch 0x2D |
Whether the pitch wheel bends this half. Default On. |
Upper DCO 1
| Parameter |
Range |
Address |
Notes |
| Range |
16', 8', 4', 2' |
Tone 1 · 11 (0x0B) |
Default 8'. |
| Waveform |
Noise, Saw, Square, Pulse |
Tone 1 · 12 (0x0C) |
Default Saw. |
| Tune |
0 to 127 |
Tone 1 · 13 (0x0D) |
Default 64. |
| LFO Mod |
0 to 127 |
Tone 1 · 14 (0x0E) |
Default 0. |
| ENV Mod |
0 to 127 |
Tone 1 · 15 (0x0F) |
Default 0. |
Upper DCO 2
| Parameter |
Range |
Address |
Notes |
| Range |
16', 8', 4', 2' |
Tone 1 · 16 (0x10) |
Default 8'. |
| Waveform |
Noise, Saw, Square, Pulse |
Tone 1 · 17 (0x11) |
Default Saw. |
| Cross Mod |
Off, Sync1, Sync2, XMod |
Tone 1 · 18 (0x12) |
Default Off. |
| Tune |
0 to 127 |
Tone 1 · 19 (0x13) |
Default 64. |
| Fine Tune |
0 to 127 |
Tone 1 · 20 (0x14) |
Default 64. |
| LFO Mod |
0 to 127 |
Tone 1 · 21 (0x15) |
Default 0. |
| ENV Mod |
0 to 127 |
Tone 1 · 22 (0x16) |
Default 0. |
Upper DCO
| Parameter |
Range |
Address |
Notes |
| DCO Dynamics |
Off, Dyna1, Dyna2, Dyna3 |
Tone 1 · 26 (0x1A) |
Default Off. |
| DCO ENV Mode |
ENV-1 +, ENV-1 −, ENV-2 +, ENV-2 − |
Tone 1 · 27 (0x1B) |
Default ENV-1 +. |
Upper Mixer
| Parameter |
Range |
Address |
Notes |
| DCO1 Level |
0 to 127 |
Tone 1 · 28 (0x1C) |
Default 100. |
| DCO2 Level |
0 to 127 |
Tone 1 · 29 (0x1D) |
Default 100. |
| ENV Depth |
0 to 127 |
Tone 1 · 30 (0x1E) |
Default 0. |
| Dynamics |
Off, Dyna1, Dyna2, Dyna3 |
Tone 1 · 31 (0x1F) |
Default Off. |
| ENV Mode |
ENV-1 +, ENV-1 −, ENV-2 +, ENV-2 − |
Tone 1 · 32 (0x20) |
Default ENV-1 +. |
Upper Filter
| Parameter |
Range |
Address |
Notes |
| HPF |
0, 1, 2, 3 |
Tone 1 · 33 (0x21) |
Four positions; 0 is the lowest setting, not off. Default 0. |
| Cutoff |
0 to 127 |
Tone 1 · 34 (0x22) |
Default 127. |
| Resonance |
0 to 127 |
Tone 1 · 35 (0x23) |
Default 0. |
| LFO Mod |
0 to 127 |
Tone 1 · 36 (0x24) |
Default 0. |
| ENV Depth |
0 to 127 |
Tone 1 · 37 (0x25) |
Default 50. |
| Key Follow |
0 to 127 |
Tone 1 · 38 (0x26) |
Default 64. |
| Dynamics |
Off, Dyna1, Dyna2, Dyna3 |
Tone 1 · 39 (0x27) |
Default Off. |
| ENV Mode |
ENV-1 +, ENV-1 −, ENV-2 +, ENV-2 − |
Tone 1 · 40 (0x28) |
Default ENV-1 +. |
Upper VCA
| Parameter |
Range |
Address |
Notes |
| Level |
0 to 127 |
Tone 1 · 41 (0x29) |
Default 100. |
| Dynamics |
Off, Dyna1, Dyna2, Dyna3 |
Tone 1 · 42 (0x2A) |
Default Off. |
| Chorus |
Off, Type I, Type II |
Tone 1 · 43 (0x2B) |
Default Off. |
| VCA Mode |
Gate, ENV2 |
Tone 1 · 58 (0x3A) |
Shown as Env Mode in the VCA section. Default ENV2. |
Upper LFO
| Parameter |
Range |
Address |
Notes |
| Waveform |
Random, Square, Sine |
Tone 1 · 44 (0x2C) |
Default Sine. |
| Delay |
0 to 127 |
Tone 1 · 45 (0x2D) |
Default 0. |
| Rate |
0 to 127 |
Tone 1 · 46 (0x2E) |
Default 50. |
Upper ENV 1
| Parameter |
Range |
Address |
Notes |
| Attack |
0 to 127 |
Tone 1 · 47 (0x2F) |
Default 0. |
| Decay |
0 to 127 |
Tone 1 · 48 (0x30) |
Default 40. |
| Sustain |
0 to 127 |
Tone 1 · 49 (0x31) |
Default 80. |
| Release |
0 to 127 |
Tone 1 · 50 (0x32) |
Default 30. |
| Key Follow |
Off, 1, 2, 3 |
Tone 1 · 51 (0x33) |
Default Off. |
Upper ENV 2
| Parameter |
Range |
Address |
Notes |
| Attack |
0 to 127 |
Tone 1 · 52 (0x34) |
Default 0. |
| Decay |
0 to 127 |
Tone 1 · 53 (0x35) |
Default 40. |
| Sustain |
0 to 127 |
Tone 1 · 54 (0x36) |
Default 100. |
| Release |
0 to 127 |
Tone 1 · 55 (0x37) |
Default 30. |
| Key Follow |
Off, 1, 2, 3 |
Tone 1 · 56 (0x38) |
Default Off. |
Upper Extensions
| Parameter |
Range |
Address |
Notes |
| DCO1 PWM |
0 to 127 |
Tone 1 · 59 (0x3B) |
Vecoven 4.x only. Default 0. |
| DCO2 PWM |
0 to 127 |
Tone 1 · 60 (0x3C) |
Vecoven 4.x only. Default 0. |
| LFO Rate Fine |
0 to 127 |
Tone 1 · 61 (0x3D) |
Vecoven 4.x only. Default 0. |
| VCF KF Fine |
0 to 127 |
Tone 1 · 62 (0x3E) |
Vecoven 4.x only. Default 0. |
| LFO Phase Reset |
Off, On Note, On Trigger, Always |
Tone 1 · 63 (0x3F) |
Vecoven 4.x only. Default Off. |
Lower DCO 1
| Parameter |
Range |
Address |
Notes |
| Range |
16', 8', 4', 2' |
Tone 2 · 11 (0x0B) |
Default 8'. |
| Waveform |
Noise, Saw, Square, Pulse |
Tone 2 · 12 (0x0C) |
Default Saw. |
| Tune |
0 to 127 |
Tone 2 · 13 (0x0D) |
Default 64. |
| LFO Mod |
0 to 127 |
Tone 2 · 14 (0x0E) |
Default 0. |
| ENV Mod |
0 to 127 |
Tone 2 · 15 (0x0F) |
Default 0. |
Lower DCO 2
| Parameter |
Range |
Address |
Notes |
| Range |
16', 8', 4', 2' |
Tone 2 · 16 (0x10) |
Default 8'. |
| Waveform |
Noise, Saw, Square, Pulse |
Tone 2 · 17 (0x11) |
Default Saw. |
| Cross Mod |
Off, Sync1, Sync2, XMod |
Tone 2 · 18 (0x12) |
Default Off. |
| Tune |
0 to 127 |
Tone 2 · 19 (0x13) |
Default 64. |
| Fine Tune |
0 to 127 |
Tone 2 · 20 (0x14) |
Default 64. |
| LFO Mod |
0 to 127 |
Tone 2 · 21 (0x15) |
Default 0. |
| ENV Mod |
0 to 127 |
Tone 2 · 22 (0x16) |
Default 0. |
Lower DCO
| Parameter |
Range |
Address |
Notes |
| DCO Dynamics |
Off, Dyna1, Dyna2, Dyna3 |
Tone 2 · 26 (0x1A) |
Default Off. |
| DCO ENV Mode |
ENV-1 +, ENV-1 −, ENV-2 +, ENV-2 − |
Tone 2 · 27 (0x1B) |
Default ENV-1 +. |
Lower Mixer
| Parameter |
Range |
Address |
Notes |
| DCO1 Level |
0 to 127 |
Tone 2 · 28 (0x1C) |
Default 100. |
| DCO2 Level |
0 to 127 |
Tone 2 · 29 (0x1D) |
Default 100. |
| ENV Depth |
0 to 127 |
Tone 2 · 30 (0x1E) |
Default 0. |
| Dynamics |
Off, Dyna1, Dyna2, Dyna3 |
Tone 2 · 31 (0x1F) |
Default Off. |
| ENV Mode |
ENV-1 +, ENV-1 −, ENV-2 +, ENV-2 − |
Tone 2 · 32 (0x20) |
Default ENV-1 +. |
Lower Filter
| Parameter |
Range |
Address |
Notes |
| HPF |
0, 1, 2, 3 |
Tone 2 · 33 (0x21) |
Four positions; 0 is the lowest setting, not off. Default 0. |
| Cutoff |
0 to 127 |
Tone 2 · 34 (0x22) |
Default 127. |
| Resonance |
0 to 127 |
Tone 2 · 35 (0x23) |
Default 0. |
| LFO Mod |
0 to 127 |
Tone 2 · 36 (0x24) |
Default 0. |
| ENV Depth |
0 to 127 |
Tone 2 · 37 (0x25) |
Default 50. |
| Key Follow |
0 to 127 |
Tone 2 · 38 (0x26) |
Default 64. |
| Dynamics |
Off, Dyna1, Dyna2, Dyna3 |
Tone 2 · 39 (0x27) |
Default Off. |
| ENV Mode |
ENV-1 +, ENV-1 −, ENV-2 +, ENV-2 − |
Tone 2 · 40 (0x28) |
Default ENV-1 +. |
Lower VCA
| Parameter |
Range |
Address |
Notes |
| Level |
0 to 127 |
Tone 2 · 41 (0x29) |
Default 100. |
| Dynamics |
Off, Dyna1, Dyna2, Dyna3 |
Tone 2 · 42 (0x2A) |
Default Off. |
| Chorus |
Off, Type I, Type II |
Tone 2 · 43 (0x2B) |
Default Off. |
| VCA Mode |
Gate, ENV2 |
Tone 2 · 58 (0x3A) |
Shown as Env Mode in the VCA section. Default ENV2. |
Lower LFO
| Parameter |
Range |
Address |
Notes |
| Waveform |
Random, Square, Sine |
Tone 2 · 44 (0x2C) |
Default Sine. |
| Delay |
0 to 127 |
Tone 2 · 45 (0x2D) |
Default 0. |
| Rate |
0 to 127 |
Tone 2 · 46 (0x2E) |
Default 50. |
Lower ENV 1
| Parameter |
Range |
Address |
Notes |
| Attack |
0 to 127 |
Tone 2 · 47 (0x2F) |
Default 0. |
| Decay |
0 to 127 |
Tone 2 · 48 (0x30) |
Default 40. |
| Sustain |
0 to 127 |
Tone 2 · 49 (0x31) |
Default 80. |
| Release |
0 to 127 |
Tone 2 · 50 (0x32) |
Default 30. |
| Key Follow |
Off, 1, 2, 3 |
Tone 2 · 51 (0x33) |
Default Off. |
Lower ENV 2
| Parameter |
Range |
Address |
Notes |
| Attack |
0 to 127 |
Tone 2 · 52 (0x34) |
Default 0. |
| Decay |
0 to 127 |
Tone 2 · 53 (0x35) |
Default 40. |
| Sustain |
0 to 127 |
Tone 2 · 54 (0x36) |
Default 100. |
| Release |
0 to 127 |
Tone 2 · 55 (0x37) |
Default 30. |
| Key Follow |
Off, 1, 2, 3 |
Tone 2 · 56 (0x38) |
Default Off. |
Lower Extensions
| Parameter |
Range |
Address |
Notes |
| DCO1 PWM |
0 to 127 |
Tone 2 · 59 (0x3B) |
Vecoven 4.x only. Default 0. |
| DCO2 PWM |
0 to 127 |
Tone 2 · 60 (0x3C) |
Vecoven 4.x only. Default 0. |
| LFO Rate Fine |
0 to 127 |
Tone 2 · 61 (0x3D) |
Vecoven 4.x only. Default 0. |
| VCF KF Fine |
0 to 127 |
Tone 2 · 62 (0x3E) |
Vecoven 4.x only. Default 0. |
| LFO Phase Reset |
Off, On Note, On Trigger, Always |
Tone 2 · 63 (0x3F) |
Vecoven 4.x only. Default Off. |
Unidentified
Bytes the unit stores and answers to that Roland never documented. The app labels them by address instead of inventing names. They are listed under Settings → Advanced → Show raw bytes, and no engine may modulate them.
| Parameter |
Range |
Address |
Notes |
| Unidentified 0x15 |
0 to 127 |
Patch 0x15 |
Undocumented byte; purpose not identified. Default 0. |
| Unidentified 0x13 |
0 to 119 |
Patch 0x13 |
Undocumented byte; purpose not identified. Default 0. |
| Unidentified 0x1A |
0 to 127 |
Patch 0x1A |
Undocumented byte; purpose not identified. Default 0. |
| Unidentified 0x1B |
0 to 127 |
Patch 0x1B |
Undocumented byte; purpose not identified. Default 0. |
| Unidentified 0x2F |
0 to 127 |
Patch 0x2F |
Undocumented byte; purpose not identified. Default 0. |
| Unidentified 0x30 |
0 to 2 |
Patch 0x30 |
Undocumented byte; purpose not identified. Default 0. |
| Unidentified 0x31 |
0 to 127 |
Patch 0x31 |
Undocumented byte; purpose not identified. Default 0. |
| Unidentified 0x32 |
0 to 1 |
Patch 0x32 |
Undocumented byte; purpose not identified. Default 0. |