Zum Inhalt springen
Knobsmith
Menü

Diese Seite ist auf Englisch.

Arpeggiator and sequencer

The MKS-70 has no arpeggiator or sequencer. The app's two pattern engines play notes into it on its MIDI channel, and the sequencer's lanes can move its parameters as well. They are the ARP and SEQ pages, beside MOD, in the header's tabs; their controls are in the bar along the bottom of the window.

The bar at the bottom

One bar runs along the bottom of every page. It is the transport of all three engines, and it is the only place that has them.

Module What it does
Clock Tempo (20 to 300 BPM), Tap (four taps in time), a Click, the bar and beat position, and the Clock chip that opens the clock setup below.
Arp On hands the master keyboard to the arpeggiator; Hold keeps the chord after the keys go up.
Seq Play / Stop the step sequencer, with its step lights.
Mod On starts the modulation matrix; the number beside it is how many routes are armed.
Panic Stops the sequencer and the arpeggiator, hands every parameter back from the modulation, and sends sustain up, All Notes Off and All Sound Off on all sixteen channels (Ctrl+.). The only Panic in the window.

The arpeggiator and sequencer share one clock, so they can run together in time. A ! lamp at the left end lights while something is wrong; click it to read why. Click ARP, SEQ or MOD in the bar to go to that page.

Clock

Click the Clock chip to set:

Setting Choices
Clock Internal: the app keeps time. MIDI Clock: follows Start, Stop and Clock from a port; the tempo becomes a read-out.
From With MIDI Clock, the port the clock arrives on.
Start Now, Next bar, or On key (the first note from the master keyboard).
Bar 2/4 to 7/4.
Arp speed / Seq speed ÷4 to ×4 against the shared clock. One engine at ×⅔ against the other at ×1 plays three against two.
Matrix rate 5 to 40 Hz. See Modulation.
Clock out With the internal clock, sends MIDI clock (24 ppqn) on the MKS-70's port so a delay or drum machine there can follow.

Following MIDI clock, the window shows the incoming tempo and TIMING STEADY, UNEASY or ROUGH; rough timing usually comes from the cable or a USB hub. NO CLOCK means nothing is arriving; WAITING means armed and waiting for Start.

Arpeggiator

The arpeggiator plays the chord you hold on the master keyboard. With no key down it plays the chord entered on screen.

  • Mode: Direction (Up, Down, Up/Dn, Up/Dn+, Dn/Up, Played, Random, Chord), Octaves (1 to 4) and Octave Travel (Up, Down, Alt).
  • Clock: Rate (1/1 to 1/32, with dotted and triplet values) and Ratchet (repeats inside a step).
  • Chord Source: Latch keeps the chord after you release the keys. Chord and transpose buttons set the on-screen chord.
  • Rhythm: up to 16 steps. Each step can rest, accent, tie, ratchet, and have a Chance and a condition such as 1:2 (every other pass). Euclid spreads the Hits evenly over the Steps; Reset and Undo restore the row.
  • Articulation: Gate (note length, up to 200 % for overlapping notes), Velocity, Velocity Source (Played, Fixed, Accent) and Accent every.

Portamento on the MKS-70 glides only between overlapping notes, so set the gate above 100 % to hear it under an arpeggio.

Sequencer

The sequencer has two pages: Notes and Lanes.

Notes

  • Rate: step length, 1/1 to 1/32.
  • Direction: Fwd, Rev, Pend (back and forth) or Rand.
  • Kbd Transpose: transposes the pattern from the lowest key held on the master keyboard.
  • Length (1 to 16 steps), Root, Span, Hits and Rotate.
  • Scale: every step is snapped to the chosen scale as it plays.
  • Melody… fills the row with a shape (Rise, Fall, Arch, Random, Walk, Octaves, Chord, Flat). Euclid, Randomise, Clear and Undo work on the row.

Each step has pitch, velocity, gate, tie, ratchet, chance and a condition. Holding the Fill button plays the steps conditioned on FILL and silences those on !FILL.

Lanes

Four modulation lanes, each aimed at an MKS-70 parameter. Each lane has its own Length of 1 to 16 steps, so a lane shorter than the note row drifts against it. A 5-step lane under a 16-step row takes 80 steps to repeat.

Each lane has a mode:

Mode What a step does
Rel (default) Moves the parameter around the panel's value. A step at the centre changes nothing. Depth scales how far it goes. Turning the knob moves the whole figure.
Abs Sets the value outright. While the lane is aimed at a parameter, that panel knob has no effect on the sound.

Fill with… draws a shape across a lane: Ramp, Fall, Arch, Curve, Random, Flip, Stairs or Flat.

A lane can target the same parameters as the modulation matrix (what cannot be modulated); its target gets a ring on the panel in the sequencer's colour. On the Original Roland setting each lane step sends a whole block.

Motion presets

The app ships 184 presets for the three engines: 46 matrix, 65 sequence, 54 arpeggio and 19 performance presets, in 12 categories (BASS, LEAD, PAD, PLUCK, ACID, RHYTHMIC, DRONE, SWEEP, CHAOS, CLASSIC, PERFORMANCE, UTILITY).

Each page has a preset strip at its top: the loaded preset, arrows to step through presets, Save and Library.

A preset's scope decides what it replaces:

Scope What it carries
Performance Everything: clock, matrix, arpeggiator and sequence.
Matrix Routings, LFOs, envelopes and macros.
Arpeggiator The arpeggiator, and the tempo it wants.
Sequence Step pattern, scale and modulation lanes.

Library opens the Preset library, filtered by scope, category, search or Mine only. Selecting a preset loads it at once, and the change lands on the next step. You can rename and delete your own presets; Copy to mine copies a factory one.

Save stores what is set up now with a name, a description, a scope and a category.

If a preset routes to a parameter your firmware setting does not have, the app loads it with that routing switched off and says which.