このページは英語です。
The panel
The panel shows one tone at a time in signal order: oscillators, mixer, filter, amplifier, then the LFO, chorus and envelopes. The Tones panel at the bottom right holds each half's patch-level settings.
Working the controls
| Action | Result |
|---|---|
| Drag up or down | Changes the value. |
| Shift + drag | Changes it four times more finely. |
| Mouse wheel | Steps the value. Shift + wheel steps by 1. |
| Double-click | Returns the control to its default. |
| Arrow keys (focused control) | Step the value; Shift steps by 1. Home and End go to the ends. |
| Right-click | Opens the assign menu: modulation sources and MIDI Learn. |
| Ctrl+Z / Ctrl+Y or Ctrl+Shift+Z | Undo / redo the last edit. |
Switches with a fixed number of positions are drawn as buttons or menus, never as knobs.
Settings → Interface sets the panel zoom, whether values show on hover or always, and the knob throw (pointer travel for a full turn).
Top bar
The strip along the top says how things stand and holds the switches you reach for mid-take.
| Item | What it does |
|---|---|
| Status and port | A lamp, the word for the connection (ANSWERING, CAN'T ASK, NO REPLY…) and the MIDI port and channel. Click for the MIDI settings. See Connecting. |
| IN / OUT | Two lamps that flash with MIDI traffic. |
| Audio | The level and a small spectrum of the audio coming back from the unit. Click to choose the input. |
| Synced / Not synced | Whether the panel shows what the unit holds. On the Original Roland setting one click reads the patch; hover for what it will do. |
| Morph | A pad with four stored sounds in its corners and a dot to drag between them. Pin it open to move the dot while you play. |
| Sampler | Opens the Sampler. |
| Keys menu | Shows who plays the MKS-70 and opens a list of every free MIDI input to choose from, with Keys play and DAW mode. |
| Antenna icon | TX: whether anything is sent to the unit at all. Green when it is; red, with the word Silent, when nothing is. |
| MIDI connector icon | MIDI Learn. Touch a control on the panel, then move a knob on your controller; the button says what it is waiting for and, afterwards, what it bound. The number beside it is how many controls are bound. |
Header
| Control | What it does |
|---|---|
| Arrows and display | Step to the previous or next patch; click the display to open the Patch Browser. The display shows the slot, patch name, channel, program and the sync state. |
| Tone, Patch, Arp, Seq, Mod | The five pages. The one you are on is lit, with a bar under it. |
| Edit Target | Upper, Lower or Both: which half the tone controls edit. |
| Listen | Upper, Both or Lower: sets the balance between the tones to one end or the centre, so you hear one tone alone or both. |
| Gear icon | Settings. |
| Bars icon | The analyser: spectrum, waveform and tuner of the returning audio. |
| Init | Red, with reset all under it. Click once (it shows Sure?), then again within four seconds, to reset the patch and both tones to a plain starting sound and send it to the unit. |
| Volume | Patch volume, read in decibels: 0 dB at full, about −55 dB at the bottom. |
Edit Target and Listen are different things
Edit Target chooses which half the knobs write to; it does not change what you hear. With Both, each tone control writes to both halves and shows the Upper value. Listen and the balance between the tones decide what you hear.
DCO 1
Range (16', 8', 4', 2'), Waveform (Noise, Saw, Square, Pulse), Tune, LFO Mod and Env Mod (how far the LFO and the envelope move the pitch).
DCO 2
Range, Waveform, Tune, Fine Tune, LFO Mod and Env Mod.
Mixer · Sync · DCO Mod
- DCO 1 Level, DCO 2 Level and Mix Env Depth faders.
- Cross Mod / Sync: Off, Sync 1, Sync 2 or X-Mod.
- DCO Env Mode and Mix Env Mode: which envelope drives the pitch modulation and the mix, normal or inverted (E1 +, E1 −, E2 +, E2 −).
- DCO Dynamics and Mix Dynamics: velocity sensitivity, Off or 1 to 3.
VCF · Filter
The 24 dB/octave low-pass filter.
- Cutoff Frequency and Resonance.
- Env Mode (E1 +, E1 −, E2 +, E2 −) and Dynamics (Off, 1 to 3).
- LFO Depth, Env Depth and Key Follow faders.
- HPF: the high-pass filter, four positions 0 to 3. Position 0 is the lowest setting, not off.
The response plot under the controls draws the filter's shape. Its horizontal axis is the cutoff value, 0 to 127, not a frequency.
VCA · Amplifier
Level, Env Mode (Gate or Env 2) and VCA Dynamics (Off, 1 to 3).
LFO
Rate, Delay and Waveform (Random, Square, Sine).
Chorus
Chorus Mode: Off, I or II.
Vecoven 4.x · PWM
DCO1 PWM, DCO2 PWM, LFO Fine, KF Fine and LFO Phase (Off, On Note, On Trig, Always). These controls appear only when the firmware setting is Vecoven 4.x. See Firmware.
ENV 1 · Filter Envelope and ENV 2 · Amp Envelope
Each has Attack, Decay, Sustain and Release faders, a Key Follow switch (Off, 1 to 3), and a plot of the envelope's shape.
Tones
One row for each half, Upper and Lower, in that half's colour.
| Control | What it does |
|---|---|
| Tone selector | Chooses which stored tone loads into this half. The list shows tone names once the app has seen them. |
| Key Shift | Transposes the half by up to 24 semitones either way. |
| Key Assign | Poly 1, Unison 1, Mono 1, Poly 2, Unison 2, Mono 2. |
| Bend | Whether the pitch wheel bends this half. |
| Porta | Portamento for this half. |
| Hold | Notes keep sounding after release, as with the sustain pedal. |
| Detune | Unison detune. Heard only with a Unison key assign. |
| Wheel LFO | How far the mod wheel (CC 1) brings in the LFO on this half. |
Above the two rows, the crossfader is the balance between the tones — the same value the Listen switch sets — labelled with the two tone names.
TONE NOT READ appears on the Original Roland setting when a half holds a tone the app has not seen. See Firmware.
Settings → Tools
- Init resets the half the Edit Target is on; Init everything is the Init in the header.
- Copy Upper → Lower and Copy Lower → Upper copy every parameter of one half onto the other, leaving the tone slot and name alone.
The result lives in the edit buffer until you press WRITE on the MKS-70.
Patch and tone names are edited in Settings → Names; see Library. Settings → Advanced → Show raw bytes lists the patch bytes whose purpose has not been identified; you do not need them to edit a sound.
MIDI Learn
Any control can follow a knob, fader or wheel on your master keyboard.
- Set a Master keyboard in Settings → MIDI.
- Right-click the control and choose MIDI Learn — move a control….
- Move the hardware control. Escape or Cancel gives up.
The control then shows the CC number; right-click it to learn another or Forget it. A learned tone control follows the Edit Target. A learned CC is not passed on to the MKS-70.